| day 1 |
- Theoretical introduction
- The structure of matter
- The structure of the atom
- Periodic table of elements
- Atomic number
- Mass number
- Natural materials
- Engineering materials
- Basic groups of engineering materials: metals and their alloys, engineering ceramics, plastics, engineering composites – similarities and differences)
- Seven characteristics of metals
- Pure metals vs. metal alloys
- Ferrous metal alloys: steel, cast steel, cast iron
- Non-ferrous metal alloys: Al alloys, Cu alloys, others
- Structure and properties
- Interactions between atoms
- Primary bonds secondary bonds
- Crystallographic lattices
- Carbon "chains"
- Amorphous structure
- Crystallographic lattices: A1, A2 and A3 – their influence on properties
- Allotropic forms of chemical elements and their influence on properties
- The occurrence of isotopes of a given element
- Mechanical and technological properties of engineering materials:
- Static tests:
- Static tensile test (Hoock's law, proportional limit, elastic limit, yield strength or proof strength, tensile strength, tensile stress, elongation, necking)
- Hardness measurements (Brinell, Rockwell, Vickers)
- Microhardness measurements
- Dynamic tests:
- Dynamic hardness measurement
- Impact strength
- Influence of chemical composition (amount of carbon)
- temperatures
- Processing status
- Chemical composition at the brittle transition temperature
- The influence of temperature (ambient, lowered, increased) on the properties of metal alloys and their technological properties
- Fatigue tests
- Sky
- Unlimited fatigue strength
- Selection and classification of materials according to groups of engineering materials
- Using material safety data sheets
- Metals and their alloys.
- Pure metals vs. alloys
- Alloy production
- Alloying elements
- Smelting (metallurgy)
- What is steel?
- Methods of obtaining (smelting steel)
- Secondary metallurgy alloying and refining
- Casting methods (COS – continuous casting of steel, casting from above, siphon casting – from below)
- Attempts to repair liquation in ingots
- Hot plastic processing
- The degree of processing and its influence on the homogeneity of the structure and therefore on the homogeneity of the properties or on the possibility of applying further technological processes, including heat treatment
- The influence of the number of phases in the alloy on the strength properties or corrosion resistance
- The most general division of alloys into alloys hardened by cold working, alloys hardened by heat treatment or casting alloys
- Eutectics - how to use it?
- Plastic processing of metals and alloys
- Mechanisms of plastic deformation
- Crystallographic structure defects and their influence on strength properties (strengthening of metals and their alloys)
- Cold forming
- The degree of work hardening and inter-operational (recrystallization) annealing - the regeneration of plastic properties
- Constantly.
- The influence of carbon on steel properties (low-, medium- and high-carbon steels)
- Division of steel according to its properties and purpose
- Unalloyed and alloyed structural steels
- Unalloyed and alloyed tool steels
- Steels with special properties: corrosion-resistant, heat-resistant, creep-resistant, valve steels, resistance steels, steels with special magnetic properties, steels for operation at low temperatures, Hadfield steels, Maraging steels
- How the amount of carbon in steel affects its properties:
- Hardness
- Machinability
- Susceptibility to plastic processing
- Weldability
- Weldability
|
| day 2 |
- Al and his feet.
- Classification
- Properties and applications of Al and its alloys
- Pure Al - physical, chemical, mechanical properties
- The amount of the element in the Earth's crust and its availability
- Method of acquiring and receiving
- Applications of Al (conductance, thermal conductivity, corrosion resistance)
- Al alloys, classification, marking
- What amounts of alloying elements determine alloys for:
- Cold plastic working
- Precipitation hardening (heat treatment)
- Casting alloys?
- Structures of Al alloys after casting and the need for plastic processing
- Crystallographic defects and their influence on strength and functional properties (hardness, formability, abrasion resistance, yield strength, tensile strength)
- The influence of the degree of cold forming on the hardening of Al and its alloys
- The need for intermediate (recrystallization) annealing – cold rolling of aluminum foil
- Cu and her feet.
- Classification
- Properties and applications of Cu and its alloys
- Physical, chemical, mechanical properties
- The amount of the element in the Earth's crust and its availability
- Method of acquiring and receiving
- Cu Applications (conductance, thermal conductivity, corrosion resistance)
- Classification of Cu alloys
- What amounts of alloying elements determine alloys for:
- Cold plastic working
- Precipitation hardening (heat treatment)
- Casting alloys?
- Base corrosion
- Electrochemical series of elements (reminder)
- Why do some metals corrode and others not?
- Chemical or electrochemical corrosion
- The influence of the number of phases inside the alloy on corrosion resistance
- Classification of corrosion phenomena
- Corrosion mechanisms
- Types of corrosive environments
- Types of corrosion damage (uniform corrosion and its rate, pitting, selective, stress, fatigue, selective, intergranular)
- Anti-corrosion: anodic, cathodic, inhibitory, sacrificial
- Surface layers (nitriding)
- Coatings (paint, enamel, rubber, plastic)
- Corrosion tests
- Thermal deposition of surface layers
- Metal or ceramic to protect against corrosion, tribological wear or thermal fatigue
- Dip coating – galvanizing, tin plating, aluminizing
- Metalizing – chrome plating (plasma or oxyacetylene torch)
- PVD processes – Physical Vapor Deposition
- CVD processes – Chemical Vapor Deposition
- Decorative coatings
- Ceramic engineering materials.
- Sintered materials and powder metallurgy
- Sintered high-speed steels PMHSS
- Materials used for multi-edge cutting inserts (carbide steels, cemented carbides, cermets, engineering tool ceramics (white, grey, black)
- Super hard cutting materials (cubic boron nitride CBN, polycrystalline synthetic diamond PKD)
- Hybrid rolling bearings
- Fully ceramic rolling bearings – properties, environment and temperatures in which they can operate
- Engineering polymers.
- General division and classification
- Properties
- Internal structure
- Material safety data sheets
- What is styrofoam?
- What is it for?
- How to obtain or shape it?
- Methods of processing thermoplastic polymers or joining/repairing them
- Engineering composites.
- Structure
- Type/size of reinforcement
- Types of reinforcing fibers (boron, glass, carbon, aramid = Kevlar)
- Fiber mats and fabrics
- Polymer matrix composites
- Metal matrix composites
|
| day 3 |
- Microscopic metallographic examination - light microscope.
- Preparation for light microscopy
- Gradations and markings of sandpaper
- Grinding rules
- Polishing – rules
- Selection of rotational speed, pressure force, amount of wetting agent, abrasive gradation in polishing pastes
- Digestion – principles
- Types of reagents, which reveals what, which to use for which alloys
- Construction and principle of operation of a light microscope.
- Total magnification
- Empty zoom
- Useful magnification
- How to match the eyepiece to the lens or vice versa
- Types of lenses
- The values that characterize each lens
- What is the resolving power of a microscope and how to increase it
- Observation techniques using light microscopy
- Examples of possible structures of metal alloys and sintered materials
- Analysis as delivered by the Manufacturer
- Possible errors at the stage of steel production in the steelworks that completely eliminate the suitability of a given steel for heat treatment
|